Produktdetaljer
ISBN
9783037858455
Publisert
2013-12-05
Utgiver
Trans Tech Publications Ltd
Vekt
200 gr
Høyde
240 mm
Bredde
170 mm
Dybde
43 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
854
Collection of selected, peer reviewed papers from the 2013 2nd International Symposium on Manufacturing Systems Engineering (ISMSE2013), July 27-29, 2013, Singapore.
The 140 paper are grouped as follows:
Chapter 1: Applied Materials Engineering and Materials Processing;
Chapter 2: Design and Engineering Researches in Mechanical Engineering;
Chapter 3: Environmental Engineering and Energy Sources Engineering;
Chapter 4: Opto- and Microelectronics;
Chapter 5: Measurements, Detection, Signal and Data Processing;
Chapter 6: Mechatronics, Control and Automation of Manufacture;
Chapter 7: Information Technology in Manufacturing Systems;
Chapter 8: Organization of Manufacture and Engineering Management.
Les mer
Selected, peer reviewed papers from the 2013 2nd International Symposium on Manufacturing Systems Engineering (ISMSE 2013), July 27-29, 2013, Singapore
- Preface and Organizing Committee
- Chapter 1: Applied Materials Engineering and Materials Processing
- Abrasive Waterjet Cutting of Aluminum Alloys: Workpiece Surface Roughness
- Investigation of Tool Life in Turning of AISI D6 Steel
- An Theoretical Study of the EDM Electrolytic Intermittent Grinding Compound Processing
- Specifics of Microstructure and Phase Composition of High-Speed Steel R6M5
- Wetting Behavior of Polymer Melts on Bulk Metallic Glasses
- Influence of Mooring Chain Steel Strength on Stress Corrosion Cracking
- Research of Electrolytic-Plasma Carbonitriding and Nitriding Influence on Phase Composition of the Stainless Steel
- Study on the Notch Strength and Notch Sensitivity of Composite Modified Double-Base Propellants
- Monitoring the EDM Characteristics of Ti-6Al-4V Process Stable Using Individual Moving Range Control Chart
- Cutting Performance of Cemented Carbide Using Single Crystal Diamond for Tool Material in Die and Mold Manufacturing
- Relationship between Controllable Process Parameters on Bump Height in ENIG
- Aluminium Surface Grain Size Analysis on RIE Treatment
- Shear Speed Analysis on Sn-3.9Ag-0.6Cu Solder
- Bump Height at Low Temperature Analysis
- Study of Changes the Tool Wear of the Cutting Tool Part of a New Cast Iron GTW 35-04 during Drilling
- Changes in Mechanical Properties of Cast Iron GTW 35-04 under the Surface Parameter during Drilling
- Fabrication and Properties of WC-Al2O3 Cemented Carbide Reinforced by Single-Walled Carbon Nanotubes
- Nanofibers/PVA Blended Nano Fibre Matrix for Nervous Tissue Regeneration
- Investigation of Surface Integrity in Path Controlled Grinding of Crankshaft Pin
- Effects of Texture Density on Tribological Performance of Laser Peen Textured Surface
- Importance of the Meshing Accuracy for Stress Evaluation in All-Ceramic Restored Teeth
- Synthesis of Peptide Lipid (N+C5Gly2C16)
- Effect of Homogenization on Recrystallization of Twin Roll Cast AA3003 Alloy
- Influence of the Top Metal Electrode on P-V Hysteresis Loops Behavior of 1-μm Thick PZT Films Deposited on a Pt/TiN/Si Substrate Prepared by MOCVD
- Preparation of TiO2/ACF in Caprolactam Tetrabutyl Ammonium Bromide Ionic Liquid
- Study of Laser Cladded Layers Structure Applied in Practice
- Research on Absorbing Property of Cement-Based Material Blending with Silica Fume and Culver Zed Fuel Ash
- Electrical Characteristics of Pt Schottky Contact to Semipolar (11-22) n-GaN Depending on Si Doping Concentration
- Numerical Simulation of the Occlusal Contacts in Roots Restored with Complete Ceramic Materials
- Effect of Ferrule Designs on Stresses of Endodontically Treated Teeth Restored with Pressed Ceramics
- Chapter 2: Design and Engineering Researches in Mechanical Engineering
- The Flow Characteristics of Nanometer Microspheres in the Vessel
- Research and Application of Special Vehicle Design Based on the FMEA
- Control Strategy of Restraining Elastic Vibration of Flexible Manipulator Arm Based on Increasing Axial Tensile Force and Structure Damp
- Stability Analysis of Elastic Vibration of Flexible Manipulator Arm Based on Routh Criterion
- Research on Air Deflector Optimal Design and Matching for Heavy-Duty Vehicle Based on Design of Experiment Technology
- Dynamic Characteristics of a Gantry Milling Machine under the Influence of Linear Guide Preload
- Compressor and Throttle Characteristics for Models
- Prediction of Temperature Distributions of Cold Forging Process for a CamBolt by FEM
- 3D Quasi-Dynamic Load Contact Analysis of Conjugate Spur Gear
- Friction Resistance between Valve Made of TiAl Alloy and its Guide Made of Phosphor Bronze
- The Influence of Fatigue Life for Shoulder Fillet Parameter in Stepped Shaft under Torsion Load
- The Performance of Steel Beam during the Cooling Phase and the Impact of Fire Parameters
- Kinematics Analysis of a 3-RRR Spherical Parallel Mechanism with Coaxial Input Shafts
- Vehicle Dynamics Model Establishing and Dynamic Characteristic Simulation
- Consider Roll of Heavy Vehicle's Modeling Research
- Equal Life Optimization of Shells Based on Kiln Axis Alignment
- Factor Analysis of Dynamic Characteristics of Balance Valve Effect on the Stability of Crane
- Numerical Simulation of Low Mach Number Steady and Unsteady Flow Past a Circular Cylinder with Preconditioning Method
- Study on Road Geometric Alignment Parameters Based on Vehicle Handling Stability Simulation
- Study on Transverse Baffle Design Parameters on Influence of Baffle Anti-Sloshing Effect by FLUENT Simulation
- Optimal Design of Wind Turbine Blades with Wilson and BEM Method Integrated
- Simulation Research on Hydraulic Brake System of Low-Floor Light-Rail Vehicle
- Numerical Simulation of Lateral Jet Interaction a Slender Body in Supersonic Flow
- Research Pressure Loss Based on Gas Liquid Two Phrase Flow Experiment System
- Numerical Simulation of Gear Shaping for Planetary Gear Based on the MASTA Software
- Dynamic Analysis of Helical Planetary Gear Train
- Spectral Element Simulation of Complex Particulate Flows
- Design and Realization of Total Performance Simulation Platform for Aircraft Engine Based on Modelica
- Research on Multi-Solver Simulation Interface of Aero-Engine Compressor
- Design and Experimental Research of a New Horizontal Wave and Flow Generation Device
- Finite Element Analysis for Double Anterior Cruciate Ligament Reconstruction Analysis
- About Determination of Stress Concentration in Bodies of a Complex Shape
- The Research on Coupling of Fluctuating Pressure and Corresponding Noise of Stilling Pool Base Slab
- Chapter 3: Environmental Engineering and Energy Sources Engineering
- Influence of Slope Gradient on Distribution Rule of Geostress Field in River Valleys
- Usage of Ti-TiO2 Electrode in Microbial Fuel Cell to Enhance the Electricity Generation and its Biocompatibility
- The Method of Tree Dynamic Modeling under Wind Field
- 3D Displacement Vector Field Analysis Technology Application for Analysis of the Slope Surface Deformation Monitoring
- Simulation Research on Mixing Structure of Kitchen Waste Biological Processor
- Preparation and Water-Absorbing Capacity of Poly(Acrylic Acid)/Montmorillonite Composites
- Improved Grey Forecasting Model for Taiwans Green Accounting
- The Study of Outdoor Water Cooling System Suitable for Cold Regions
- Electric Vehicle Battery Distribution Network Optimization
- Effect of Limited Irrigation on Water Consumption and Grain Yield of Spring Maize (Zea Mays)
- Effect of Limited Water Supply on Photosynthetic Characteristics of Spring Maize (Zea Mays)
- CFD Simulation of Insulation Performance of Air Curtain Used in the Cold Store
- Effect of Water with Anti-Freezing Material Based Cooling for Split Air Conditioning System
- Simulation Study of HTP Decomposition within Silver Screen Catalyst Bed of the Monopropellant Gas Generator
- Chapter 4: Opto- and Microelectronics
- Design of Dimmable Quasi-Resonant Fly Back LED Driver Based on OZ9992
- Computational Simulation of High-Concentration Erbium Media for Lasers Development
- Research on Length Optimization of Fiber of Length Measurement Method Based on Opto-Electronic Oscillator
- 5mm × 5mm Sized Slug on High Power LED Stress and Junction Temperature Analysis
- Chapter 5: Measurements, Detection, Signal and Data Processing
- Micro-Bridge Structure Design of UFPA with Highly Sensitive Pixels
- Diagnostic Methods Assigned for Monitoring the Operating Fault State of Production Equipments
- An Incremental Locally Linear Embedding Algorithm with Non-Negative Constraints of the Weights
- The State Recognition for Rotary Machines Based on Fractal Theory and Neural Network
- Super-Resolution Imaging in a Close-Packed Synthetic Aperture Digital Holographic Microscopy
- Study on Hidden Information of Microelectronic Packaging Image Series with PCA
- Measurement of Static Performance of Inductive Proximity Switch for a Mobile Robot
- Research on PCA Based Sensor Fault Detection and its Application
- Key-Frame Extraction Method from Single-Lens Undersea Video Sequences
- The Nonparametric Confidence Interval for the Process Capability Index C*pmk
- An Extrema Extension Method Based on Support Vector Regression for Restraining the End Effects in Empirical Mode Decomposition
- An Improve Firefly Algorithm and its Application
- A Novel Bat Algorithm of Solving III-Conditioned Linear Equation Group
- Testing and Analysis of Several Global Optimization Algorithms
- Intrinsic Dimensional Correlation Discretization for Mining Task
- Near-Infrared Spectroscopy Signal Extraction and Processing Design
- Experimental Analysis of Laser Scattering Patterns for the Surface Inspection of Crystalline Wafers in Solar Cell
- Chapter 6: Mechatronics, Control and Automation of Manufacture
- The Preliminary Study of Wall Climbing Firefighting Rescue Robot for High-Rise and Super High-Rise Building
- Automatic Current Sharing Technology in the DCS Power System Applications Research
- Based on Orthogonal Experiment Method PID Simulation Control of Pumping Unit
- A Research for Angle Optimization of the SRM Used in Electric Actuator of Valves
- Design and Implementation of Constant Palstance Control System of Combine Cylinder Based on STM32
- Design of Micro-Positive Pressure Control System for Clean Plant Air Conditioning
- A Self-Repairing Control Scheme for Quadrotor Helicopter via Active Disturbance Rejection Control
- Research on Searching Guidance of TV Guided Missile
- Two-Tone Colored Petri Net and its Application in PLC
- Design of Robot Lawn Mower Based on Computer Vision
- A Comprehensive Approach of Advanced Error Troubleshooting in Intelligent Manufacturing Systems
- Broadband Low-Frequency Vibration Energy Harvester with a Rolling Mass
- Bottleneck Simulation of Two-Lane Traffic CA Model with Turn Signal
- RANSAC Feature Based Master-Slave Tracking System for Multi-AGV
- Robotic Three-Dot Force Feedback to Suppress Surface Contact Slipping in Robot Drilling
- State Feedback Controller Design for CSTR Based on Kalman Filter
- Task-Oriented Servo Loops Control of a 6-DOF Manipulator for Rescue Robot
- A Novel and Efficient Method for Digital Printing
- Induced Power Aggregation Operators and their Applications in Group Decision Making
- Design and Implementation of Control System in Warm Extrusion Forming Process Manipulator for Steel Connecting Sleeve
- Piezoelectric Bulk Material for the Fabrication of Membrane Actuators Using Surface Electrodes for Actuation
- On Reliability Study of a New Generation of Crane Controllers
- Development of Robotic System for Free-Form Surfaces Polishing Based on CAM Data
- Adaptive Control for NC Position Table Base on Radical Basis Function Neural Network
- Chapter 7: Information Technology in Manufacturing Systems
- Intelligent Remote Medical Care System by Use of a Multiple of Network Protocol Integration
- The Platform of SCRP and the Construction of Low-Carbon Supply Chain
- Safety Analysis for Complex Dynamic Systems
- Research and Design of Intelligent Library System Based on RFID
- Research on the Developing Platform for Complex Product
- An Improved Bat Algorithm and its Application in the Logistics Distribution Center Location Problem
- Internet Public Opinion Monitoring Model Based on Cloud Computing
- Review of Sequence Planning of Virtual Assembly
- Application of Rapid Prototyping Technology in Intelligent Optimization Design Area
- An Improved Two-Sided Assembly Line Balancing Algorithm Based on Heuristic Rules
- Special Software Development for Tire Vulcanization Simulation
- Three-Phase Heuristics Algorithm for Solving JIT Materials Delivery Problem in Discrete Production System
- Application of Flexible Combine-Clamp in Digital Rapid Production for Aircraft Tube
- Three-Dimensional Process Design of Large Complex Mechanical Product
- Chapter 8: Organization of Manufacture and Engineering Management
- Risk Sharing Research Based on Utility Theory in Urban Rail Transit of BT Mode
- The Analysis and Forecast about the Supply and Demand of China's Rubber Raw Materials Based on Grey Model
- Research and Implementation of Auto Parts Proportion Model
- Research of Stochastic Demand Spare Parts Inventory for Equipment Maintenance
Les mer
Produktdetaljer
ISBN
9783037858455
Publisert
2013-12-05
Utgiver
Trans Tech Publications Ltd
Vekt
200 gr
Høyde
240 mm
Bredde
170 mm
Dybde
43 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
854