/

Precision Die Design

Ibhadode, Akii Okonigbon Akaehomen
Heftet / 2009 / Engelsk

Produktdetaljer

ISBN
9780878491513
Publisert
2009-06-30
Utgiver
Vendor
Trans Tech Publications Ltd
Vekt
600 gr
Høyde
240 mm
Bredde
170 mm
Dybde
13 mm
Aldersnivå
P, UP, 06, 05
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
252

Forfatter
Ibhadode, Akii Okonigbon Akaehomen

Precision Die Design

Ibhadode, Akii Okonigbon Akaehomen
Heftet / 2009 / Engelsk
Ibhadode, Akii Okonigbon Akaehomen
Heftet / 2009 / Engelsk
Nettpris:
2.840,-
Laveste pris siste 30 dager: 2.840,-
Levering 7-20 dager
Klikk og hent

Volume is indexed by Thomson Reuters BCI (WoS).
This book presents a new method for the design of the precision dies used in cold-forging, extrusion and drawing processes. The method is based upon die expansion, and attempts to provide a clear-cut theoretical basis for the selection of critical die dimensions for this group of precision dies when the tolerance on product diameter (or thickness) is specified. It also presents a procedure for selecting the minimum-production-cost die from among a set of design alternatives.

Les mer
<p>by the Die Expansion Method</p>
  • Preface
  • Notation
  • Table of Contents
  • 1. Introduction
  • 1.1 Precision Dies. 1.2 The Die Expansion Method.
  • 1.3 Scope of Method
  • 2. Die Container Design for Monoplex Dies
  • 2.1 The Die Container
  • 2.2 Die Expansion
  • 2.3 Design Criteria. 2.4 Monoplex Design
  • 3. Multiplex Die Containers
  • 3.1. Introduction
  • 3.2 Duplex Die Containers
  • 3.3 Triplex Die Containers
  • 3.4 Quadruplex Die Containers
  • 3.5 N-Plex Die Containers
  • 3.6 Radial Interferences and Diameters of Cylinders in Multiplex Dies
  • 3.7 Force-Fit Loads in Cylinder Assembly
  • 3.8 Effects of Die Container Parameters
  • 3.9 Die Geometric Constants for Higher Order n-plex Dies
  • 3.10 Total Elimination of Die Expansion
  • 4. Application to Processes
  • 4.1 Introduction. 4.2 Die Geometric Constant as a Function of Die Diameter Ratio
  • 4.3 Maximum and Allowable Die Stresses. 4.4 Design Procedure for Completely Closed Cavity Dies
  • 4.5 Impact Extrusion Dies
  • 4.6 Conical Converging Dies
  • 4.7 Direct Extrusion Dies
  • 4.8 Indirect Extrusion Dies
  • 4.9 Wire/Rod Drawing Dies
  • 4.10 Tube Drawing
  • 5. Tube Drawing
  • 5.1 Introduction. 5.2 Theoretical Analysis
  • 5.3 Effects of Die Parameters
  • 5.4 Design Procedure
  • 5.5 Application to a Typical Design Problem
  • 6. Die Production Cost
  • 6.1 Introduction. 6.2 Assumptions
  • 6.3 Die Production Cost Function
  • 6.4 Cost of Press-Fitting of Cylinders
  • 6.5 Cost of Die Material. 6.6 Die Selection Criteria
  • 6.7 Procedure for Selection of Die Container
  • 6.8 Case Study
  • Exercises
  • References
Les mer

Relaterte produkter

Volume is indexed by Thomson Reuters BCI (WoS).
This book presents a new method for the design of the precision dies used in cold-forging, extrusion and drawing processes. The method is based upon die expansion, and attempts to provide a clear-cut theoretical basis for the selection of critical die dimensions for this group of precision dies when the tolerance on product diameter (or thickness) is specified. It also presents a procedure for selecting the minimum-production-cost die from among a set of design alternatives.

Les mer
<p>by the Die Expansion Method</p>
  • Preface
  • Notation
  • Table of Contents
  • 1. Introduction
  • 1.1 Precision Dies. 1.2 The Die Expansion Method.
  • 1.3 Scope of Method
  • 2. Die Container Design for Monoplex Dies
  • 2.1 The Die Container
  • 2.2 Die Expansion
  • 2.3 Design Criteria. 2.4 Monoplex Design
  • 3. Multiplex Die Containers
  • 3.1. Introduction
  • 3.2 Duplex Die Containers
  • 3.3 Triplex Die Containers
  • 3.4 Quadruplex Die Containers
  • 3.5 N-Plex Die Containers
  • 3.6 Radial Interferences and Diameters of Cylinders in Multiplex Dies
  • 3.7 Force-Fit Loads in Cylinder Assembly
  • 3.8 Effects of Die Container Parameters
  • 3.9 Die Geometric Constants for Higher Order n-plex Dies
  • 3.10 Total Elimination of Die Expansion
  • 4. Application to Processes
  • 4.1 Introduction. 4.2 Die Geometric Constant as a Function of Die Diameter Ratio
  • 4.3 Maximum and Allowable Die Stresses. 4.4 Design Procedure for Completely Closed Cavity Dies
  • 4.5 Impact Extrusion Dies
  • 4.6 Conical Converging Dies
  • 4.7 Direct Extrusion Dies
  • 4.8 Indirect Extrusion Dies
  • 4.9 Wire/Rod Drawing Dies
  • 4.10 Tube Drawing
  • 5. Tube Drawing
  • 5.1 Introduction. 5.2 Theoretical Analysis
  • 5.3 Effects of Die Parameters
  • 5.4 Design Procedure
  • 5.5 Application to a Typical Design Problem
  • 6. Die Production Cost
  • 6.1 Introduction. 6.2 Assumptions
  • 6.3 Die Production Cost Function
  • 6.4 Cost of Press-Fitting of Cylinders
  • 6.5 Cost of Die Material. 6.6 Die Selection Criteria
  • 6.7 Procedure for Selection of Die Container
  • 6.8 Case Study
  • Exercises
  • References
Les mer

Produktdetaljer

ISBN
9780878491513
Publisert
2009-06-30
Utgiver
Vendor
Trans Tech Publications Ltd
Vekt
600 gr
Høyde
240 mm
Bredde
170 mm
Dybde
13 mm
Aldersnivå
P, UP, 06, 05
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
252

Forfatter
Ibhadode, Akii Okonigbon Akaehomen

Relaterte produkter