Preface and CommitteesA Grain Boundary Formulation for the Analysis of Three-Dimensional Polycrystalline MicrostructuresComparisons of High-Temperature Structural Analysis Results on the Medium-Scale PHE Prototype under the Steady-State and Trip Conditions of a Small-Scale Gas LoopEffect of Niobium Film on Corrosion Resistance of AZ91D Magnesium AlloyThe Measurement of Mechanical Properties of Thermal Barrier Coatings by Micro-Cantilever TestsCrack Growth by Dimensional Reduction MethodsNondestructive Evaluation of Polyurethane Materials Using Transient ThermographyNumerical Modelling of Particulate Composite with a Hyperelastic MatrixFracture Toughness of PIR Foams Produced from Renewable ResourcesModelling of Discontinuous EnvironmentInfluence of Finite Element Modeling Choices in the Assessment of Stress Concentrations at Fatigue Prone Locations in Orthotropic Bridge DecksNumerical Analysis of Femoral Neck Angle Influence on Stress Distribution of Cemented Austin Moore Hip ProsthesisAdvanced Natural Stitched Composite Materials in Skin-Stiffener of Wind Turbine Blade StructuresInterfacial Shear Strength of Carbon Fiber Reinforced PolypropyleneEffect of Surface Treatment on Creep Property of Jute Fiber Reinforced Green Composite under Environmental TemperatureMicro-Scale Cantilever Testing of Linear Elastic and Elastic-Plastic MaterialsThe Influence of the Epoxy Interlayer on the Assessment of Failure Conditions of Push-Out Test SpecimensFracture and Damage Characterization of Natural Fiber CompositesModeling of Damage and Failure of Dual Phase Steel in Nakajima TestMicromechanical Modeling for the Evaluation of Elastic Moduli of Woven CompositesCharacterization of Metal Magnetic Memory of Thermal Damage Correlated with Initial Cumulative Fatigue Damage for Laser Cladding Remanufacturing TechnologySEM In Situ Study on Pre-Corrosion and Fatigue Cracking Behavior of LY12CZ Aluminum AlloyAnalysis of Stress Intensity Factor for Cracked Flattened Brazilian Disk: Part I – Analysis Method and Pure Mode I CrackAnalysis of Stress Intensity Factor for Cracked Flattened Brazilian Disk: Part II – Mixed-Mode CrackThermo-Mechanical Stress near Apex of a Bi-Material Wedge by a Novel Finite Element AnalysisSimulation of Spall Fracture Based on Material Point MethodBuckling Reliability Analysis for the Cylindrical Shell with Initial DefectsTo Research Residual Stress Using Finite Element AnalysisNumerical Simulation of Underwater Explosion Based on Material Point MethodNumerical Simulation of Fatigue Behavior of Honeycomb Sandwich PanelsThe Debond Fracture of Sandwich Plate with Corrugated Core Using Cohesive Zone ElementStudy on a Numerical Calculation Method of Fatigue Behavior in Glare PanelInvestigation of Residual Stress Distribution in Clad 2024 T3 after Laser PeeningInvestigation on the Corrosion Effect of Friction Stir Welded AA2024 T3 Aluminum Alloy JointsDistortion Induced Fatigue Analysis of Steel BridgesMaterial Properties and Fatigue Safety Evaluation of Old Metal BridgesDamage Monitoring and Evaluation Using AE Sensors for Existing Concrete BridgesRepair and Service Safety Evaluation of a Fire Damaged Concrete BridgeScaling Effects on the Tensile Strength of Fibrous CompositesAnalysis of Fatigue and Cumulative Damage Characteristics for Concrete in Freezing-Thawing EnvironmentResidual Fatigue Life Analysis of Submarine Pressure Structure Based on Probabilistic Fracture MechanicsGeometrical Parameters Influencing a Hybrid Mechanical CouplingFatigue Test of Small Sized AZ31 Magnesium Alloy Using Micropillar SpecimenFatigue Behavior of A356 Cast Aluminum Alloy Microstructurally Modified by Friction Stir Processing under Low Strain Rate ConditionLoad Influence on the Behavior of Micro-Crack in the Particulate CompositePressure Pipe Damage: Numerical Estimation of Point Load EffectQuasi-Static Simulation of Crack Growth in Elastic Materials Considering Internal Boundaries and InterfacesDeterioration of FRC Plate due to Explosion and Change of TemperatureMonitoring Fatigue Cracks and Stress Intensity Factors Based on the Distributed Dislocation TechniqueComputational Characterization of Micro-To Macroscopic Deformation Behavior of Double Network HydrogelMultilevel/Multiobjective Design of Composite StructuresThe Role of Grain Size on Deformation of 316H Austenitic Stainless SteelExperimental Investigation of the Influence of the Bond Conditions on the Shear Bond Strength between Steel and Self-Compacting Concrete Using Push-Out TestsExperimental Study of the Influence of the Initial Notch Length in Cubical Concrete Wedge-Splitting Test SpecimensMicro-Analyses of Small Cracks in 6061-T6 Aluminium Alloy Subjected to High-Cycle FatigueFatigue Properties of Solution-Treated Type 304 Stainless Steel after NitridingFatigue Crack Growth of Alloy 7050-T7451 Plate in L-S OrientationStructural Design and Finite Element Analysis of Composite Wind Turbine BladeDetermination of Intensity Factors for Interfacial Cracks in TIP MaterialsFailure of Composite T-Joints in Bending with Through-the-Thickness Reinforcement: Stitching Vs Z-PinningInvestigation on T11-Stress for Semi-Elliptical Surface Cracks in Finite Thickness Plates under Remote TensionInvestigation of Thermal Damage and the Consequent Fatigue Property of Laser Surface Heat Treated ComponentA 3-Dimensional Model Related to Stress-Strain-Time of Rock SaltsExperimental Research on Interlaminal Shear Strength of GFRP Bridge Decks under Simulated Concrete EnvironmentVibration Fatigue Behavior of 2024-T62 Aluminum Alloy Cantilever Beam under Different Vibration StateSimulation of Pylon Emergency Break-Away of Large Commercial AircraftDynamic Mechanical Behavior of Two Fiber-Reinforced CompositesNumerical Simulation of Compression-After-Impact Process of Composite LaminatesDeposition Process and Interface Properties of Electro-Thermal Explosion Sprayed WC/Co CoatingGrain-Boundary Segregation of Phosphorus and Inter-Granular Fracture Behavior under Low Tensile StressesEffect of the Neodymium Content on Mechanical Properties of the Electro-Brush Plated Nano-Al2O3/Ni Composite CoatingFE Simulation Methods to Predict Welding Residual StressesStudy on the Pin-Load Distribution of Multiple-Bolted Composite to Metal JointsThe Sensitivity of the Foam-Core Parameters under Impact LoadingDynamic Anti-Plane Behaviors on Two Dissimilar Piezoelectric Media with an Interfacial Non-Circular CavityAnalysis of Crack Tip Field in Materials with Creep BehaviorThe Conservation Laws and Path-Independent Integrals for Piezo-Magnetic MediaScattering of Anti-Plane SH-Wave by Multiple Cylindrical Inclusions in Elastic Semi-SpaceMultiscale Simulation of the Size Effect of Nano-IndentationJ-Integral and its Dual Form Based on Finite Deformation TheoryStudy on the Diffusion Coefficient in NGS under Low Tensile StressPressureless Sintering and Properties of Boron Carbide-Titanium Diboride Composites by In Situ ReactionGalvanic Corrosion of Titanium/Cu-Ni Alloy/High Strength Steel Multiphase Material System in SeawaterWear Failure Behavior of Steel Surface with Palygorskite Powders as Lubricant AdditivesFatigue Assessment of Trimaran Structure Based on Simplified ProcedureA Comparative Study between Steel Grillage and SPS Stiffening Plate Based on FEA Eigen Value AnalysisYield Criterion and Crack Tip Plastic Zone of Nickel-Based Single CrystalInteraction of Elliptical Inclusion and Crack in Half-Space under SH-WavesInfluence of Welding Conditions on Residual Stresses of Multi-Pass Tube Sheet WeldsStudy on Mode I Quasi-Static Growing Crack in a Rigid-Viscoelastic Material Interfacial CrackAnalysis of Interface Deformation of Steel-Concrete-Steel Sandwich BeamReliability Analysis for Stiffened Plate on the Maximum Entropy MethodAn Enhanced Time-Reversal Method for Impact Damage Monitoring on Plate-Like StructuresExperimental Study on Residual Strength of Panels with Multiple Site DamageDamage Analysis of 2D Woven Composite Laminates Containing an Open-Hole under Tensile LoadingsA New Approach to Determine Dynamic Strength Model Parameters under Taylor Impact TestA Novel Testing Method for Measuring Through-Thickness Properties of Thick Composite LaminatesNumerical Simulation of Compressive Residual Strength for Damaged Composite LaminatesA Research on Characterization for Damage Tolerance of Composite LaminatesThe Simulation of Low-Velocity Impact on Composite Laminates with the Damage Model Based on StrainInvestigation into Damage of Stainless Steel Mesh/ALPlate Multi-Shock Shield under Hypervelocity AL-Spheres ImpactNumerical Simulation of Hypervelocity Impact on Mesh Bumper Causing Fragmentation and EjectionAnalysis of Crack Arrest by Electromagnetic Heating in Metal with Oblique-Elliptical Embedding CrackEffect of Characteristic Parameters of Exponential Cohesive Zone Model on Mode I Fracture of Laminated CompositesExtended Finite Element Method for Fracture Mechanics and Mesh Refinement Controlled by Density FunctionEffects of Surface Roughness on the Fatigue Life of Alloy SteelCorrelation between Alternating Temperature Accelerated Aging and Real World Storage of Composite PropellantExperimental Research on Fracture Toughness of High Grade Line PipeStress-Strain Analysis of Composite Propellant under Cyclic Temperature LoadsDamage Detection for Structural Health Monitoring Using Ultrasonic Guided WavesThe Research on Wood Fiber/Stainless Steel Net Electromagnetic Shielding Composite BoardLow Cycle Fatigue Behaviors of TI-6AL-4V Alloy Controlled by Strain and StressAnalysis of Stress Singularity near the Tip of Artificial CrackAn Evaluation on the Restrained Shrinkage of Ultra-High Performance ConcreteStructural Strength Evaluation of a Stainless Railroad CarStudy of the Characteristic of Composite Sandwich Panel with Cut-Out under Compression LoadSize Effect of PHE Prototype on High-Temperature Structural IntegrityHigh-Temperature Structural Analysis on the Small-Scale PHE PrototypeCharacterization of Ductile Failure Behavior of the Ferritic Steel Using Damage Mechanics Modeling ApproachThermal and Static Analysis of an Insulation Block from Recycled Polymer HDPE for Solution of Thermal Bridges in Wall-Footing DetailDiagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic TestsNumerical Analysis of a Steel Frame Building with Soft-Storey Failure under Ground Motion ExcitationRelation between Structural Size and the Discretization Density of Brittle Homogeneous Lattice ModelsMatching Asymptotic Method in Propagation of Cracks with Dugdale ModelFormability Evaluation of Non-Crimp Carbon Fabric by Non-Contact 3D Deformation Measurement SystemModelling Micro-Damage in Granular SolidsLoad and Environmental Effects on the Corrosion Behavior of a Ti6Al4V AlloyFatigue Crack Nucleation and Growth Mechanisms for Ti6Al4V in Different EnvironmentsModeling Delamination of Interfacial Corner Cracks in Multilayered StructuresCrack Modelling Using the Material Point Method and a Strong Discontinuity ApproachNumerical Simulation of Crack Tip Behavior under Fatigue LoadingDelamination Threshold Load of Composite Laminates under Low-Velocity ImpactInelastic Seismic Behavior without and with Over-Resistance Effects of 10-Story Building RC Damaged due to the 1985 Earthquakes in Mexico CityAccurate Description of Near-Crack-Tip Fields for the Estimation of Inelastic Zone Extent in Quasi-Brittle MaterialsApplication of the Mesh Superposition Technique to the Study of Delaminations in Composites Thin PlatesDeterministic and Probabilistic Earthquake Scenarios for the Seismic Risk Analysis of URM BuildingsMicromechanics Damage Analysis in Fiber-Reinforced Composite Material Using Finite Element MethodOn the Direction of a Crack Initiated from an Orthotropic Bi-Material Notch Composed of Materials with Non-Uniform Fracture Mechanics PropertiesFracture Behaviour of Thin Sheet Stainless SteelTransient and Steady State Regimes of Fatigue Crack Growth in High Strength SteelEstimation of Shear Behavior of Ultra High Performance Concrete I Girder without Shear StirrupsA Local Compression Tests of UHPC Anchor Blocks for Post-Tensioning TendonsImpact Identification in Composite Stiffened PanelsElectro-Mechanical Impedance Technique for Structural Health Monitoring of Composite PanelsDynamic Response Analysis of Lining Structure with Primary Defects for Tunnel under Moving Train LoadingMonitoring Analysis of Tunnel Construction in a New Subway Line Down-Through an Existed LineSMART Platform for Structural Health Monitoring of Sensorised Stiffened Composite PanelsMicromechanical Characterisation of Microstructure in Weld Heat Affected Zone of Structural SteelTwo Scale-Based Continuum Damage Model for Brittle Materials under Thermomechanical LoadingThe Applicability Study on the FRP-Concrete Composite Bridge Deck for Cable-Stayed BridgesImprovement of Fatigue Crack Growth Behavior in the Case of the Cracked Specimen with Relatively Narrow WidthDynamic Crack Problems Using Meshless MethodInvestigation of Damping Characteristics of Metals by the Use of Inverted Torsion Pendulum MethodMechanical Characteristics of BambooRelationship between Crack Extension Behavior and Fatigue Life of C/C CompositesInfluence of Adhesive Layer on Actuation of Lamb Wave SignalsEvaluation of Setting Time in Ultra High Performance Concrete