Volume is indexed by Thomson Reuters CPCI-S (WoS)
X-ray applications and techniques are gaining importance and are moving to the forefront of science. A powerful tool with many advantages, X-ray applications and techniques present a route for rapid, hassle-free, non-destructive, safe and accurate analysis. This book contains a compilation of papers, all related to X-ray techniques, which are applied in various areas of science and technology, namely in research and industry. This publication aims to showcase the current diversity and versatility of X-ray related techniques. With contributors from all around the world, this publication of compiled papers will relate a host of X-ray related techniques with aims and the eventual findings, all of which are presented in a short and concise manner. It is believed that this book will be a good scientific literature which provides clear and important information on X-ray related ventures.

Les mer
<p>Selected, peer reviewed papers from the International Conference on X-Ray and related Technique in Research and Industry (ICXRI 2012), July 3-5, 2012, Pulau Pinang, Malaysia</p>
  • Message from Guest Editors and Conference Committees
  • Growth of Nanocrystalline PbS Thin Films by Solid-Vapor Deposition
  • Preparation of Co0.5Zn0.5Fe2O4 and Co0.5Mn0.5Fe2O4 Nanoferrites by Co-Precipitation Method
  • The Effect of CaCO3 Addition on Physical Properties of ZnO-Based Crystal Glaze
  • Surface Morphology and Si 2p Binding Energy Investigation of Multilayer Porous Silicon Nanostructure
  • Compositional and Structural Characterization of Heterostructure InGaN-Based Light-Emitting Diode by High Resolution X-Ray Diffraction
  • Determination of Crystallite Size in Synthetic and Natural Hydroxyapatite: A Comparison between XRD and TEM Results
  • The Effects of Cr2O3 Addition on Fracture Toughness and Phases of ZTA Ceramic Composite
  • Photoluminescence Properties of Porous Silicon Nanostructures (PSiNs) with Optimum Electrolyte Volume Ratio of Photo-Electrochemical Anodization
  • Structural and Surface Studies of Undoped Porous GaN Grown on Sapphire
  • Characterisation of Phases and Lattice Parameter in Eutectic and Hypoeutectic Al-Si-Mg-Ce Cast Alloy
  • Structural and Thermoelectric Properties of Bi0.4Sb1.6Se3xTe3(1-X) Quaternary Compound
  • Influence of Substrate’s Alignment Strategy to the Growth of ZnO Nano-Petals via Solution-Immersion Method
  • Crystallization of Potassium Calcium Silicate from Modified Industrial EAF Slag
  • Identification of Mixed-Layer Mineral of Cambodian Clays and their Phase Changes upon Firing
  • Effect of Microstructural Evolution on the Properties of Friction Stir Processed Al 6061 Alloy under Different Cooling Conditions
  • Crystal Structure Optimization and Semi-Empirical Quantum Chemical Calculations of N-(3,4-Dichlorophenyl)-3-Oxo-Butanamide
  • Properties of Mortar Containing Rice Husk Ash at Different Temperature and Exposed to Aggressive Environment
  • Mechanical Alloying of Fe-Nb-N with Different Ball to Powder Weight Ratio for the Formation of Fe-NbC Composite
  • XRD Analysis and Tensile Properties of Attapulgite Clay Filled Polyvinyl Alcohol/Corn Starch Blend Films
  • Intermetallic Compound Formation on Solder Alloy/Cu-Substrate Interface Using Lead-Free Sn-0.7Cu/Recycled-Aluminum Composite Solder
  • The Effect of Amount of Surfactant and Types of Drug on Amorphous Silica Drug Delivery System (DDS)
  • Friction Stir Processing of Mild Steel to Enhance its Surface Hardness
  • Gel Oxidation of Titanium for Biomedical Application
  • Production of Porous Cordierite through Sol-Gel Polymeric Sponge Method
  • Growth of ZnO Nanostructures at Different Temperatures without Catalyst by Wet Thermal Oxidation Process
  • The Influence of Temperature on the Oxide Layer Formation of Aluminized Carbon Steel
  • Intermetallic Evolution of Sn-3.5Ag-1.0Cu-0.1Zn/Cu Interface under Thermal Aging
  • WO3-Polypyrrole Nanocomposite as Catalyst in Azelaic Acid Synthesis from Oleic Acid
  • P-Incorporated TiO2 Nanotubes for Methyl Orange Degradation
  • The Effects of Combustion Agents on the Formation of Bi-Based Compounds Synthesized Using the Soft Combustion Method
  • Study on the Influence of Synthesis Temperature of Anatase TiO2 Nanoparticles for Electrophoretic Deposition
  • XRD Analysis of Cu-Al Interconnect Intermetallic Compound in an Annealed Micro-Chip
  • Discovery of WO3/TiO2 Nanostructure Transformation by Controlling Content of NH4F to Enhance Photoelectrochemical Response
  • XRD and EDXRF Analysis of Anatase Nano-TiO2 Synthesized from Mineral Precursors
  • X-Ray Diffraction Study of High Velocity Oxy-Fuel (HVOF) Sprayed Cr3C2-NiCr Coating
  • A Simple Method to Prepare Indium Oxide Nanoparticles on Si (110)
  • The Effect of Stoichiometry to the Phase Formation of Barium Titanate
  • Heterogeneous Combustion of Ti/Si/C Powders with Estimated Ti3SiC2 Routes Morphologies
  • Thermal, Electrical and Physical Properties of Recycled Copper Filled Epoxy Composites
  • X-Ray and Morphological Characterization of Al-O Thin Films Used for Vertically Aligned Single-Walled Carbon Nanotube Growth
  • The Effect of MgO Dopant on the Dielectric Properties of CaCu3Ti4O12 Ceramics
  • Characterization of Potential Used Rubber Seed Coat Waste for the Removal of Remazol Brilliant Blue R Reactive Dye
  • Investigation of Grain Size Effect on the Impedance of CaCu3Ti4O12 from 100 Hz to 1 GHz of Frequency
  • Hybrid Multiwalled Carbon Nanotubes/Minerals as Potential Fillers for Polymer Composites
  • Structural and Optical Properties of Nanocrystalline CdO Thin Film Growth by Solid-Vapor Deposition
  • Investigation into the Metal Oxide Surge Arrestors' Failures
  • Structural and Microstructure Relationship with Fracture Toughness of CeO2 Addition into Zirconia Toughened Alumina (ZTA) Ceramic Composites
  • X-Ray Diffraction Study of Cold Sprayed Ni-20Cr and Ni-50Cr Coatings on Boiler
  • Microstructure Evolution of Sn-3.5Ag-1.0Cu-0.5Ni/Cu System Lead Free Solder under Long Term Thermal Aging
  • Iron Salt Concentration Effect to the Precipitation of Iron Oxide Nanoparticles Conjugated Antibody
  • Morphology and Intermetallics Study of (Sn-8Zn-3Bi)-1Ag Solder under Liquid-State Aging
  • Synthesis, Characterisation and Catalytic Activity of Sol-Gel Derived Silica-Mineral Acids
  • Luminescence of SrAl2O4:Eu2+, Dy3+ Ceramics Synthesized at Different Firing Condition
  • Study on Effect Recyclability of Ru/Bentonite-TiO2 Catalysts in Glycerol Hydrogenolysis Reaction Using X-Ray Photoelectron Spectroscopy (XPS)
  • Phase Formation of α-Cordierite Using Different Sintering Profile
  • Preparation of Cellulose Microfibrils from Banana (Musa acuminata) Pseudo-Stem Waste
  • Formation of Titanium Silicon Carbide (Ti3SiC2) via Modified Self-Propagating High Temperature Synthesis (SHS) System through Arc Melting
  • Effect of Ball-Milling Parameter on the Synthesis of MWCNT/Alumina Hybrid Compound
  • Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)
  • Synthesis and Growth Mechanism of Catalyst-Free ZnO Nanowires Using Chemical Vapour Deposition
  • Studies of Cell Growth on TiO2 Nanotubes
  • X-Ray Spectrometry Study on Historical Decorative Glasses in Thailand: Lanna-Style Glass
  • Production of Biodiesel from Non-Edible Jatropha curcas Oil via Transesterification Using Nd2O3-La2O3 Catalyst
  • X-Ray Diffraction Studies of CdxZn1-xS Thin Films Prepared by Spray Pyrolysis Technique
  • Influence of Silica and Zirconia Particles as Filler Loading on the Radiopacity of Dental Resin Composites
  • Synthesis and Gas Sensing Properties of SnO2 Nanostructures by Thermal Evaporation
  • Formation of Well Aligned ZnO Nanorods Grown on Silicon Substrate by Chemical Bath Deposition Method
  • Compressive and Wear Resistance of Alumina Reinforced Fe-Cr Matrix Composites
  • Structural and Optical Properties of In0.27Ga0.73N/Si (111) Film Grown Using PA-MBE Technique
  • Preparation and Characterization of Biphasic Calcium Phosphate Coatings on 316L Stainless Steel Fabricated by Electrophoretic Deposition
  • Tin Oxide Doped on Activated Dolomites as Efficient Catalyst for Biodiesel Production
  • Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method
  • Porous Ceramic Supports Prepared from Porcelain Mixture
  • Preparations and Characterization of Sago Starch Dispersion and Modification
  • Synthesis and Characterization of MWCNT/Dolomite Hybrid Compound as Potential Composite Fillers
  • Bamboo Sawdust as a Reduction Agent in Leaching Applications: Characterization Studies
  • Crystallization of TiO2 Nanotubes Arrays Grown by Anodization of Ti in Organic Electrolyte
  • Computational Studies of Electronic Structures and Hyperfine Interactions of Muonium in Tetraphenylgermane
  • Role of NbC Grain Growth Inhibitor on Microstructure and Hardness of WC-Stainless Steel Hard Metals
  • Single Step Combustion Synthesis for the Preparation of Bismuth Titanate Ceramics for Potential Applications
  • Synthesis and Characterization of Ba0.3Sr0.7ZrO3 Ceramic Thick Films Prepared by Sol-Gel Technique
  • Oxidative Degradation Monitoring of Natural Rubber Using S K-Edge X-Ray Absorption near-Edge Spectroscopy (XANES)
  • Mesoporous Silica Sol-Gel as Catalyst for the Synthesis of Alkylpolyglucosides
  • Electrical and Optical Characterization of Mg Doping in GaN
  • Preliminary Evaluation of Mukah Clay Deposits
  • Fabrication of Nanoporous Aluminum Oxide via a Two-Step Anodisation Process
  • Fundamental Characterisation of Dredged Marine Sediments from Kuala Perlis Jetty by XRF, XRD and FTIR
  • Properties of Aluminium Thin Films on Polyimide Plastics as Back Contacts in Thin Film Silicon Solar Cells
  • Quantitative Energy Dispersive X-Ray Flourescence Analysis of Low Alloy Steel by Regression and Modified Fundamental Parameter Techniques
  • Pb(Zr0.52Ti0.48)O3 Ceramics Synthesized Using Planetary Ball Mill
  • Dehydration Studies of Biomass Resources for Activated Carbon Production Using BET and XRD Techniques
  • Modeling Microfibril Angle and Tree Age in Acaciamangium Wood Using X-Ray Technique
  • Characteristics of Airborne Pm2.5 and Pm2.5-10 in the Urban Environment of Kuala Lumpur
  • The Effects of Superheating Treatment on Distribution of Eutectic Silicon Particles in A357-Continuous Stainless Steel Composite
Les mer

Produktdetaljer

ISBN
9783037855607
Publisert
2013-02-06
Utgiver
Vendor
Trans Tech Publications Ltd
Vekt
1050 gr
Høyde
240 mm
Bredde
170 mm
Dybde
28 mm
Aldersnivå
P, UP, 06, 05
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
550