8th International Conference on Advanced Materials and Engineering Materials (ICAMEM 2019)

Selected, peer reviewed papers from the 8th International Conference on Advanced Materials and Engineering Materials, (ICAMEM 2019), April 18-19, 2019, Hong Kong, China

• Preface
• Chapter 1: Composites
• Preparation and Properties of Tea Polyphenol Modified Graphene Oxide/Epoxy Resin Composites
• Two-Stage Sintering of Alumina-Y-TZP (Al₂O₃/Y-TZP) Composites
• Pressing and Bonding Strength of Metal Matrix Composite
• Influence of Molding Pressure on Properties of Al₂O₃- Al Composite Materials Sintered via Vacuum Sintering Method
• Kinetic Processes in Polydisperse Systems: Experience of Practical Approximation
• Chapter 2: Nanomaterials and Nanofabrication
• Synthesis of Diamond-Like Structures by Method of Mechanochemical Treatment of Nano-Carbon Materials (Taunit)
• Optical and Electrical Properties of Diamond-Like Carbon Thin Film with Deposition by ECR-CVD System
• Highly Increased Flow-Induced Voltage Generation on Hybrid Membranes of Monolayer Graphene and Single-Walled Carbon Nanotubes
• Effect of Reaction Time on Surface Nano-Structure of TiN Oxide Nanofilm by Hydrothermal Method
• Toughened Poly(Trimethylene Terephthalate) by Melt Compounding with Functionalized Graphene Oxide Nanocomposites
• Controlled Hydrothermal Synthesis of K₂Ti₆O₁₃ Nanowires and their Photo-Electronic Response
• Electrochemical Degradation of p-Nitrophenol on Cu Nanowires and Nanocubes
• Photoelectric Response Difference between KTaO₃/ Au and K₂Ta₂O₆/Au Nanocrystals Resulting from Potassium Tantalate Structure
• Preparation and Characterization of In Situ Nanocomposites of Graphene Nanosheets/Polyurethane
• Crystalline Morphology and Crystallization Behavior of Poly(Trimethylene Terephthalate)/Functionalized Graphene Oxide Nanocomposites Prepared by Melt Compounding
• Microstructure Analysis and Preparation of Graphene Reinforced Aluminum Matrix Composites
• Analysis of Electroluminescence Application on Display
• Preparation and Characterization of 3-Glycidoxypropyltrimethoxysilane Functionalized Graphene Oxide
• Chapter 3: Properties of Steel and Alloys, Processing Technologies and Manufacturing Processes
• Low Cycle Fatigue Life Evaluation According to Temperature and Orientation in Nickel-Base Superalloy
• Effect of Frequency to Ultrasonic Vibration-Assisted Wire-EDM
• Deformation Analysis of TC4 Titanium Alloy Shell Material
• Cr12MoV Die Repair Experiment Based on Laser Cladding with Wire
• Effect of Citric Acid on Cerium Conversion Coating of Hot-Dip Galvanized Steel
• Subsurface Stress Distribution and Failure of PPS Thrust Bearings under Rolling Contact Fatigue in Water
• Study on the High Temperature Creep Behavior of 30Cr25Ni20 Heat-Resistant Steel
• Effect of Different Hole-Making Technology on Fatigue Properties of Directionally Solidified Alloy IC10
• Control of Microstructure and Properties of Welded Joints of Heavy Structures of Low Alloy High Strength Steels
• Effects of Mixed Mode Loading Conditions on Fatigue Crack Growth Rate
• Fundamental Research on Gasification Dephosphorization with Coke Powder Reducing Converter Molten Slag
• Experiments and Regression Analysis of Grinding Hardened Layer Depth Based on Transverse Feed
• Throughput Estimation Model of Cluster Tool in Semiconductor Manufacturing
• An Intelligent Optimization System for PIM Process
• Formation of Feed-Direction Burr in Axial Vibration Drilling
• Main Features of High Speed Machining Chucks and their Selection
• Failure Observation of 3D-Printed Thrust Bearing Specimens with Inner Defects in Water Conditions
• Welding Repair of High Chromium Cast Iron Defects
• Research on Base Welding Technology of Alkaline Welding Rod with Arc Method
• New Low Alloy High Strength Steel Welding Procedure Evaluation
• Study on Welding Technology of Low Alloy High Strength Steel
• Study on Fatigue Life of Straight Hole Plate of Directionally Solidified Alloy IC10
• Study on Particle Modified ABS in 3D Printing
• Effect of Different Aging System on Microstructure and Mechanical Properties of X2A66 Alloy
• Optimization of Precipitation Phase Type and Mechanical Properties of X2A66 Alloy by Pre-Deformation Treatment
• Study on Fatigue Properties of Copper Alloy Netting Structure
• Chapter 4: Measurements and Modeling of Materials Properties and Materials Behavior
• Evaluation of Wickability of Quick Dry Inner Wear
• A Study of Wickability of Gauze Products for Infant
• Synthesis and Clay Anti-Swelling Properties of Diethyl Dodecyl Allyl Ammonium Chloride
• Microstructure Investigation of He⁺- Implanted and Post-Implantation-Annealed 4H-SiC
• Thermal Management of a Li-Ion Battery for Electric Vehicles Using PCM and Water-Cooling Board
• Observation of Tribological Fatigue Fracture on PEEK Shaft with Artificial Defect under One-Point Rolling Contact by Using 2.5D Layer Method
• Multilayered Elastic Medium under Axisymmetric Loading and Surface Energy
• Effect of Aspect Ratio on Horizontal Field Magnetoresistance
• Observation of Crack Growth Behavior of 400μm Cracks in 4.762mm Silicon Nitride Balls under Cyclic Compressive Load
• Effects of CeO₂ Addition on Slip - Cast Yttria Tetragonal Zirconia Polycrystals Toughened Alumina (ZTA)
• Chapter 5: Materials for Biomedical Application
• Antibacterial Properties among Different Concentration of Bioactive Glasses
• Comparison of Three Commercial Latex and Non-Latex Orthodontic Elastic Bands
• Chemical Constituents of the Aerial Parts of Scoparia Dulcis and Anti-Cancer, Anti-Inflammatory Activities
• Preparation, Characterization and Hemostatic Properties of Chitosan Caffeates
• Comparison of Mechanical Properties of Plain and Reversed Curve Nickel-Titanium Archwires
• Shear Bond Strength of Experimental Light-Cured Orthodontic Adhesives
• Chapter 6: Materials and Technologies for Construction
• Effect of Shrinkage Reducing Admixture on Shrinkage and Crack Properties of Cement Based Materials
• Water Resistance Modification of Magnesium Oxychloride Cement with H₃PO₄/Na₂O·xSiO₂·nH₂O
• Correlation between Unconfined Compressive Strength and Penetration Index Obtained from DCP Tests for Cemented Lateritic Soils
• A Model for Bond Strength in Presence of Corrosion in Concrete
• Effect of High Temperature Process on Microstructure and Properties of Industrial Steel Slag Cement
• Experimental Study on Permanent Deformation of Fine Sandy Subgrade Filling in Coastal Region
• Rebar Anchor Plate Research and Application
• Evaluation on Sulfuric Acid Resistance of Concrete Protected by Biomimetic Coating Mortar
• Axial Behavior of Columns Strengthened with Seismic RC Jacket Section
• Chapter 7: Materials and Technologies for Chemical Production and Processing
• Synthesis of Cerium Phosphate White Pigments from Cerium Oxalate
• Desorption of Mercury Complex from Fe-Modified Montmorillonite Adsorbent Membrane
• Ni_0.75Fe_0.25 Coated Tubular GDC Anode for Cathode-Supported IT-SOFC with High Anode Porosity
• Congo Red Dye Removal Using Ca-Al Layered Double Hydroxide: Kinetics and Equilibrium
• Effects of Extraction Conditions on Total Phenolic Content and Total Flavonoid Content of Roselle (Hibiscus sabdariffa L.) Extracts
• Response Surface Methodology Optimization for Extraction of Natural Anthocyanins from Vietnamese Carissa сarandas L. Fruit
• Microfluidic Chip Injection Photo Solidification Molding Study on Reaction Kinetics
• Characterization and Photocatalytic Activity of Microspheres ZnO by Hydrothermal Method
• Synthesis of New Phosphate and the Evaluation as Scale Inhibitor in Oilfield
• Modification of Ligustrum vulgare Leaves Extract as Eco-Friendly Corrosion Inhibitors in Oil Fields
• Study on Source Analysis of the Cation in Produced Water from Sulige Gas Field and Anti-Scaling Measures
• Preparation and Evaluation of Phosphate Scale Inhibitor for Oilfield Produced Water
• Catalytic Cracking of Oleic Acid over Zeolites
• Effect of Compatibilization on the Melt Properties of Mixed Waste Plastics
• Effect of Extraction Process on Extraction Yeild, Total Polyphenol Content and Antioxidant Activity of Jasminum Subtriplinerve