2nd International Symposium on Advanced Materials and Application (ISAMA 2019)

Selected, peer reviewed papers from the 2019 International Symposium on Advanced Materials and Application (ISAMA 2019), January 18-20, 2019,Seoul, South Korea

• Preface
• Chapter 1: Metallurgical and Metalworking Technologies
• Study on Factors which Make CBN Insert can Turn S45C Steel Have Surface Roughness Less than Ra 0.4
• Weldability of Similar and Different Metallic Materials
• Computer Simulation and Analysis of the Parameters of the Drawing Process of Thin Wire from the Alloy Pd-5Ni
• Study of the Influence of Conditions of Combined Casting and Rolling-Extruding and Two-Stage Annealing on the Structure and Properties of Semi-Finished Electrical Products from an Al–Zr System Alloy
• Computer Modeling and Analysis of the Energy-Power Process Parameters of the Combined Machining of Alloys Al-Mg System
• Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods
• Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small Groove on PET Plate Using A356 Die
• 600 mm-Wide Strip Casting Using Single Roll Caster Equipped with Scraper
• Effect of Latent Heat of Aluminum Alloys on Bonding between Strips in Clad Strip Cast by a Twin-Roll Caster
• Chapter 2: Functional Ceramics and Fiber Composites
• Mechanical Properties of PP/clay Nanocomposites Prepared from Masterbatch: Effect of Nanoclay Loadings and Re-Processing
• Influence of Sintering Temperature on Physical and Mechanical Properties of Hydroxyapatite-Calcium Titanate Composite
• Physical and Mechanical Properties of Bi_0.5(Na_0.81K_0.19)_0.5TiO₃ Ceramic Modified by KNbO₃
• An Analysis of Air Permeability of Cotton-Fibre-Based Socks
• Examining Moisture Management Property of Socks
• Mechanical and Rheological Properties of High Density Polyethylene Reinforced Polyvinyl Alcohol Fiber Composites
• Nanomaterial Production by Arc Discharge Sputtering of Silicon-Graphite and Silica-Graphite Composite Anodes
• Corrosion Behaviors of Reinforcing Steel in Concrete with Various Moisture Contents
• Chapter 3: Chemical Technologies in Environmental Engineering, Bioindustry and Energy Production
• Predictive Study of Combustion Temperature of Liquefied Petroleum Gas (LPG) on the Spherical Packed-Bed Porous Burner
• The Influence of Stainless Steel Mesh Porous Burner on Drying Kinetics of Nile Tilapia
• Green Synthesis of Iron Oxide Nanoparticles for Lead Removal from Aqueous Solutions
• Microwave Assisted Extraction (MAE) Process of Tannin from Mangrove Propagules Waste as Natural Dye for Coloring Batik tulis
• "Green" Bleaching Process of Sugar Palm (Arenga pinnata) Flour by Using Sodium Salt and Ozone Technology
• Fundamentals and Applications of Red Light-Emitting Diodes (LEDs) In Vitro Plant Growth on Tomato Lycopersicon esculentum Mill
• Production of Microsphere Polystyrene Using Solution Enhanced Dispersion by CO₂ Supercritical Fluids (SEDS)
• Chapter 4: Materials and Technologies in Construction
• Geometric Analysis of a Modular, Deployable and Reusable Structure
• Study on Service Life of OPC and HPC in Marine Environment
• Confinement Shear Effect in Fiber Composites
• Original Experimental Campaign of Indentation Instrumented on Aggregates of Non-Hazardous Waste Incineration Bottom Ash to Study the Heterogeneity of their Rigidity
• Chapter 5: Mechanical Properties and Durability of Structural Materials
• Failure on Bearing Cooler Coils Connector of Hydroelectric Power Plant
• Buckling Analysis of Variable Stiffness Composite Cylindrical Shells Based on Hermite Curves
• Elastoplastic Equilibrium of a Hollow Thick-Walled Radially Inhomogeneous Ball
• Stresses Analysis of Hypocycloidal Gear Transmissions