Selected peer-reviewed extended articles based on abstracts presented at the 18th International Symposium on Metallography, Fractography and Materials Science (2022)

Aggregated Book

• Preface
• Invited Lectures
• Development of Materials for Solid State Hydrogen Storage
• Slag from Modern Copper Production Found in Bergwerk, Burgenland, Austria
• Influence of Surface Machining on Development of Stress Corrosion Cracking of Distribution Wheels of Main Circulation Pump in Nuclear Power Plants
• Chapter 1: Microstructure, Properties and Processing of Structural Materials
• Processing and Mechanical Properties of (Hf-Ta-Zr-Nb-Ti)C
• Application of Composite Filament with the Addition of Metallic Powders in 3D Printing
• Highly Accurate Structural Analysis of Austempered Ductile Iron Using EBSD Technique
• Optimization of the Manufacturing Process of Sintered Fe-Mn-Cr-Mo-C Steels Using ANOVA
• Direct Production of Tin Bronzes from Copper and Cassiterite
• Microstructure-Properties Characterization of Selective Laser Melted Biomedical Co-28Cr-6Mo Alloy
• Effect of Rare-Earth Doping on Dynamic Magnetic Properties of FeGa Alloy
• Optimization of Raster Point Deposition Methodology for Deformation Analyses
• Formation of Alpha-Case Layer during Oxidation of Ti6Al4V Surface by Annealing at 1050 °C and Change of Microstructure after Different Cooling Rates
• Microstructure Analysis of Progressive Secondary AlSi7Mg0.6 Alloy with Higher Fe Content Using Electron Metallography Techniques
• Comparison of Microstructure and Properties of Nickel-Copper Alloy Prepared by Casting and Laser Powder Bed Fusion Process
• Formation of Sulphides in As-Cast GOES Thin Strips
• Characterisation of a San Mai Steel Composite for the Manufacture of Knives
• Numerical Simulation of the Welding Process during the Main Circulation Pump Impeller Repair
• A Study of Cut Surface after the Abrasive Water Jet Application on the MS1 Material Prepared by DMLS Method
• The Influence of Progressive Cladding Technologies on Layers Quality
• Chapter 2: Corrosion
• Identification of Corrosion Mechanisms of Stainless Steel with Metallography Cross Sections
• Influence of Cavitation in Seawater on the Etching Attack of Manganese-Aluminum-Bronzes
• Chapter 3: Fractographic Analysis
• Microstructure and Fatigue Behavior of High-Performance Aluminum Alloy Al2024 Produced by Laser Powder Bed Fusion
• Analysis of Cracks of Thermostats Casings Made of Brass
• The Fractographic Analysis of Tensile and Fatigue Fracture Surfaces in Secondary A356 Aluminum Alloy with a Higher Concentration of Iron
• Fracture Mechanisms of Austenitic Steel Caused by Dynamic Tests
• High-Temperature Low Cycle Fatigue of Nickel-Based Superalloy IN738LC
• Metallography of Fractured Aluminium Alloys for the Transmission System ́s Elements
• Investigation of Fatigue Failure in Electric Locomotive Axle
• Dynamic Fracture Characteristics of High-Strength Steel
• Creep Resistance and Microstructure Evolution in HR3C-P92 Heterogeneous Welds
• Analysis of Tribodegradation Factors Limiting the Life of the Molds
• Chapter 4: Nanomaterials and Nanotechnologies
• Preparation and Fracture Analysis of Advanced Layered Composite with Graphene-Coated Alumina Nanofibers
• Influence of Ligands on Physicochemical Characteristics of Magnetic Nanoparticles
• Carbon Fibers Doped by Binary Phosphides as an Electrocatalytic Layer for PEM Electrolysers
• Chapter 5: Sample Preparation for Metallography
• Evaluation of Sample Preparation Importance for Digital Image Correlation during Cold Deformation
• Automation of Metallographic Sample Etching Process